|
George Herrin
|
 |
« on: February 11, 2010, 07:17:14 pm » |
|
Rules that differ from the 2009 rulebook have been highlighted in bold faced red print.
Additional rule changes may be implemented as needed. Please monitor the National website-www.golawnmowerracing.com- or your local chapter for updates.
The American Racing Mower Association (ARMA) is an organization designed for lawn mower racers by lawn mower racers. This sport provides racers, their families and friends the opportunity to get involved with compe:censored:ive racing that is affordable.
This rulebook provides the standards that regulate the operations within ARMA. Maintaining safe, compe:censored:ive racing is the primary purpose of this do:censored:ent and with the cooperation of all members, we can collectively keep this sport as it was intended, FUN.
A lot of time, money, and energy have been spent on mower fabrication, engine building, and traveling to and from race venues. Keep that in mind when racing and race clean and safe. Although mishaps will happen from time to time on the track, lets look out for each other and keep ourselves and our mowers in the same conditions when we started the race as when we leave.
General Regulations
1. On Track Regulations
Any deliberate actions to cir:censored:vent the safety features of a mower at either a Local Chapter or National Points Series race will result in sanctions for the driver. These sanctions will include a minimum of the following:
Total loss of points for said event
Suspension from 2 race events immediately following the incident
Based upon the severity of the incident sanctions may be increased at the discretion of the Local Chapter representatives and/or their board of directors or the ARMA National Board of Directors (dependent upon where the incident occurred).
Actions to deliberately violate the rules for any mower class will result in the same
sanctions found above.
a. No alcoholic beverages or illegal drugs are allowed within the controlled area of the racing activity, including the pit area.
b. Any person who is actively participating in a race event (at any level) who has consumed alcoholic beverages, illegal drugs, or controlled substances that is mind and/or motor skills altering may not participate in any capacity.
c. Completing a safe pass is the responsibility of the overtaking driver. No bumping will be tolerated. This means if you initiate a pass and during execution you realize you cannot complete the pass in a safe manner then it is up to the overtaking driver to return to a safe position on the track while avoiding contact with other racers. You will gain more respect by taking yourself out then placing the other racers in an unsafe situation causing personal injury and mower damage.
d. If you are being overtaken by another racer and it is clear that they are faster make room for the overtaking racer and let them pass.
e. Blocking is part of racing but not to the point where it causes a crash.
f. The racer that causes an incident will restart the race at the end of the field. This will be determined by the track officials.
g. Flags will be used to communicate to the racers the following on track conditions:
1) Green: The race/practice is underway when displayed.
2) Yellow: CAUTION, DANGER. No passing on the entire track and the drivers will form a
single line at a safe pace speed and close up to the leader and follow the starters
directions.
3) Yellow & White: The field is not bunched up for restart. If this is displayed, close it up.
4) Red: Stop all racing action immediately and shut off your engine. This flag is used in
emergency situations where personal injury has occurred or the track is blocked.
5) Black: This for driver or equipment infractions. The driver must safely exit the track and consult with the Chief Steward. A furled black flag is a warning to a driver to clean up his/her act or receive the full black flag indicating he/she needs to exit the track.
6) White: One lap to go. Crossed white and green indicates race is halfway complete.
7) Checkered: End of race or practice session. Winner may choose to make a victory lap with the checkered flag. The remaining drivers will complete the lap and safely exit the track to the pit area.
h. Driver must keep both hands on the steering wheel, except to momentarily operate other controls. Drivers body may not be intentionally positioned out of the mower seat onto or over the mower fender.
i. If you leave the course during the race re-enter the track as close as possible to the exiting point. Exiting the course and reentering in order to gain position will result in the driver being placed at the rear of the field.
j. If the mower stalls move the mower to a safe place at least 10 feet off course.
k. Unsafe off track driving will not be tolerated.
l. Drivers must attend all drivers meetings. If an unforeseen cir:censored:stance forces a driver to miss the meeting they shall begin at the rear of the field after meeting with the Chief Steward for a briefing on the days racing information.
m. Starting positions will be determined by random draw for a rolling start
2. Pit Area and Track Regulations
a. Mower pit speed is 5 MPH maximum.
b. Long pants, closed shoes and shirts are required in the track area.
c. Refueling: Driver must dismount and engine must be shut off when fuel is added. A fire extinguisher (Liquid Fire Rated) must be in the hands of a crew member any time fuel is added to a hot machine.
d. Mower must be completely stopped before driver dismounts.
e. Track crews are under the direction of the Track Steward at all times.
f. The driver is responsible for the conduct of his/her guests and crew, even while on
the track.
g. Only authorized personnel and drivers shall enter the racing course during racing activity. All individuals entering the pit area, including crew members and guests, must sign a release discharging ARMA from liability. All individuals entering the track area must have a wrist band.
h. No pets are allowed on the racing course.
j. ARMA reserves the right to limit pit space. Campers and RVs may be permitted
on race day only if space permits.
j No vehicles other than racing mowers and official vehicles such as tow mowers
shall be on or near the track.
3. Driver Eligibility
a. Drivers must be members of the American Racing Mower Association.
b. Prepared class drivers (Super Stock class and above) must be at least 16 years of age. Drivers under 18 years of age must have an approved parents consent form on file.
c. Drivers participating in Junior Prepared must be at least 10 years old and no older than 15 years old. No driver under 16 years old may operate or compete on a mower other than a JP mower.
d. All drivers must sign a release discharging the ARMA from liability.
e. Drivers should conduct themselves in a professional, mature manner while on the track. If a driver feels there is an issue requiring attention, he/she will bring the issue to the Chief Steward in an appropriate manner. Failure to do so will result in removal from the remainder of the days racing action.
4. Safety Equipment
a. Every driver must wear an automobile racing or motorcycle-type full-face helmet
approved by the U. S. Department of Transportation or the Snell Foundation.
b. The helmet must fit snugly and be securely buckled when driver is on the track.
c. Goggles or a face shield are required. Glasses are not adequate protection.
d. All drivers must wear long pants, long sleeved shirt, neck brace, full-fingered
gloves and leather over the ankle footwear on the track. Chest protectors and other
anti-abrasive suits are highly recommended. No loose clothing on the track.
5. Mower Eligibility
a. Events are open to all riding type lawn mowers and garden tractors (with tires 20 or less) that were mass-produced and commercially available to mow residential lawns. Zero turn riders are not permitted. The mower may be modified from its original configuration as noted in section 7 General Mower Specifications Modified Classes.
b. Final determination of eligibility and classification is up to the technical inspector.
c. Organizers reserve the right to reject at any time any mower, which in their opinion, represents an attempt to defeat the spirit of these rule, even though it complies with the letter of them.
6. Technical Inspection
a. All mowers entered in any ARMA event must inspected for compliance by the
Technical Inspector prior to participating in practice or racing.
b. Drivers must complete the registration process and sign insurance releases prior to
entering the tech line.
c. Drivers may be questioned on the content of this do:censored:ent and must pass in order
to practice or race.
d. All required safety equipment must be present at technical inspection.
e. Any driver, guest, crew member or official that displays behavior that is considered dangerous to other drivers, guests, crew members or spectators may be removed from the event by authorized event officials.
f. If it is the opinion of an ARMA official designee (Local Chapter President or other officer, ARMA Board of Directors member) that a Stock, Super Stock or Junior Prepared mower is out of compliance with rules for these classes said mower may be internally examined. This may include removal of cylinder heads, opening of transmissions, etc. See sanctions in Section 1
g. Initial build inspection will occur at the first National Points Series Race a driver attends. Subsequent inspections will be for safety issues. If a mower is involved in an on-track incident at a National Points Series Race, it will receive a full inspection at the next National Points Series Race before being permitted to return to compe:censored:ion.
7. General Mower Specifications- Modified Classes (All classes except Stock)
a. Cutting blades must be removed.
b. Cutting decks must be securely mounted in near stock location. Only Pro-X and Super Modified mowers may simulate a cutting deck. Decks may extend beyond the tire sidewalls a maximum of 2. Decks must be as wide as the body edge or running boards whichever is wider.
c. Mowers must maintain a minimum of 2.5 ground clearance under the lowest point of the deck except Super Modified class mowers.
d. Mowers must maintain a minimum of 4 of ground clearance under the lowest point of the frame except Super Modified classes. Unused brackets and non-structural material may be removed to gain clearance.
e. Exhaust design is open, but must terminate away from the driver and compe:censored:ors, in a rearward and downward direction without creating a safety hazard.
f. Starter and functional battery must be on board, either electric or pull rope in all classes except Pro-X.
g. Rear wheels must be secured to the rear axle with shaft locks, center bolts or
thru-bolts.
h. All non-stock mowers shall have an automatic, throttle closing device.
i. Kill switch lanyard length shall be as short as necessary to effectively stop the mower as quickly as possible. Lanyard length shall not exceed 40. This device must be commercially available for racing and/or recreational vehicles such as ATVs, jet skis snowmobiles, etc. Homemade and/or magnetic switches are not allowed.
j. Mower brakes on any Sportsman or X series mower must be upgraded to a brake system on the rear axle.
k. Brakes may be hydraulic or mechanical.
l. Throttle and brake control may be relocated.
m. The steering wheel, seat, body and frame must be centered between the right and left wheels. Offset is not permitted. See Super Modified Rules.
n. Drive line may be modified from the engine pulley to the rear wheels. All classes except Pro-X and Super Modified must use a shift able lawnmower transmission or transaxle. Vari-drives may be used if originally equipped.
o. No centrifugal or torque converter clutches permitted in any class except Pro-X and Super Modified.
p. Rear axle may use open differential, locked, live or solid axle. No single wheel drive. Aluminum rear axles are permitted.
q. Wheels must be the same size on each axle, of any origin, but made of metal. Duel or tandem wheels are forbidden.
r. Front axle and steering may be modified or fabricated. Front axles may be pinned, bolted or welded into place. No suspension allowed. All modifications and fabrications are subject to the judgment of the technical inspector.
s. All steering linkage must be ball-type or spherical threaded rod ends.
t. Footholds and seat side boosters must be minimally designed so as not to entangle body parts. Foot guards should be no higher than 4 from the bottom of the bar to the top and be flush with the bottom of the frame. Bars should be 2 off of the rear tire. With wheels turned to extreme position, there should be 2 of clearance between tire and bar.
u. External ignition systems and aluminum flywheels are authorized.
IMPORTANT SAFETY NOTE
It is highly recommend that there be no alterations to a stock flywheel. This is to include removing the magnets and/or removing metal from the flywheel in various locations. Altered flywheels are not tested under any standards for safety and may not withstand high rpms. Starting with the first ARMA insured race of the 2011 race season (2011 race season starts with the first race following the 2010 ARMA finals), mowers with lightened/altered flywheels will not be permitted. Flywheels will be required to be stock (including magnets) or billet.
v. All steering and wheel retention fasteners must terminate with locking nuts, castellated nuts with cotter pins, washers with new cotter pins, shaft locks, or locking bolts. Cotter pins, E-rings and C-rings alone, bent nails, hitch pins, over center pins and quick-release pins are not permitted.
w. Mowers may reach a maximum width of 38sidewall to sidewall except Super Modified classes.
x. Carburetors must be of lawnmower origin and from the same manufacturer as the engine block. Prepared mowers participating in the Mini-Sportsman class and above will be required to have dual return springs on the throttle.
y. Mowers may only operate on pump gasoline. No additives or additions to the fuel are allowed. No nitrous oxide, rocket fuel, alcohol or other oxidizers are permitted. No combustion enhancing substances may be added to the crankcase oil or air cleaner assembly. Any attempt to cir:censored:vent this rule will result in disqualification from the event. No electric fuel pumps.
z. All engines must be naturally aspirated. Blowers, turbochargers, and water injection systems are not allowed.
aa. Tires must be lawn tractor tires in all classes except Pro-X and Super Modified.
bb. Subs:censored:uted steering wheels are permitted. They may not be mounted offset unless originally mounted offset. Steering wheel consists of a 360 degree circular device. This wheel may not be pegged or have steering devices attached to them. Hand throttle and brake controls are permitted.
cc. All positively charged terminals must be insulated with a cover or heavy tape. Battery must be well secured on the mower.
dd. All mowers must be safe and complete with all parts and panels in places with no missing fasteners. Machines that have been involved in a on-track incident resulting in removal of body parts will only be allowed back on the track after the mower has been inspected to determine if its return would present a safety issue.
ee. All exposed sprockets, chains, rotating shafts and pulleys must be fitted with metal guards 1/8 inch thick minimum deflecting a broken chain downward and preventing entanglement with mower parts.
ff. Mowers must be free of sharp edges, projections and protrusions.
gg. A rear bumper is highly recommended and should be no wider than the rear tire width, fabricated from either 1 or Ύouter diameter tubing with radius bends and installed a maximum of 2 from closest surface of the rear tire. Recommended height of no higher than 8. The bumper should be centered on the rear axle. The intent of the bumper is to prevent mowers from climbing the rear tires and making contact with a driver. No other bumpers are permitted, even those offered as factory options.
hh. Seats must be present and of lawn mower origin except Super Modified classes. Seat is defined as being a separately attached device on which the driver will place his body during racing compe:censored:ion. They should be securely mounted to the mower, on the center of the frame. Seats may be adjusted more towards the front or rear of the mower along the center line to help achieve better weight balance for handling.
ii. The lowest portion of the seat pan should not be mounted lower than the top of the rear tires except in Super Modified classes.
jj. Sheet metal should be as delivered from the factory with the following exceptions:
Subs:censored:utions:
Where original factory sheet metal is not available or is damaged in a way that renders it unsafe or unusable sheet metal from another similar model mower that would otherwise be eligible to race may be used.
Replacement sheet metal must fit properly and be as close in shape to the factory panel as possible.
Subs:censored:ute sheet metal should be attached to the frame in as close to the original position as possible.
All panels must be securely fastened so as not to create a safety hazard.
Subs:censored:uted panels must be modified to fit properly and safely.
Minimal under hood mounting brackets are acceptable.
Panel subs:censored:ution is provided in order to give the opportunity for a racer to run a mower that might otherwise be sidelined. Panels may not be subs:censored:uted simply to modify or customize a mowers appearance. Panel subs:censored:utions that make a mower look radically different than other mowers in a class will not be allowed.
Fiberglass parts are permitted as subs:censored:ution for metal parts when metal parts are not available.
Modification:
The hood and/or its components may be modified to provide clearance to allow tires to turn and steer without contact with sheet metal.
Sheet metal maybe bent or cut to allow for clearance of modifications otherwise allowed such as air cleaners, exhaust, brakes, clutches or other controls.
Openings cut in sheet metal shall not be more than 2 inches from the obstruction.
Fenders may be modified to allow for tire clearance issues due to chassis lowering as well as for handling purposes. Allowable modifications include:
Trimming fenders such that there remains ½ of clearance between the fender edge and the top of the tire.
Flaring of the fender such that there remains ½ of clearance between the fender edge and the top of the tire.
1 of vertical material must remain on the fender. This will ensure the structural integrity of the fender.
Fender trimming should follow the contour line of the fender, not merely remove sheet metal in the immediate area.
Fender trimming or flaring that results in sharp edges will not be permitted.
Removal:
Any sheet metal originally on a mower may not simply be removed. A mower originally delivered with fenders must have fenders. A mower originally delivered with a hood must have a hood.
ll. Race numbers should be a minimum of 3 high and of a sharply contrasting color from its background, and be visible from all four sides of the mower. Mowers without numbers or mower with same number will be assigned one during registration. Mowers will also have class designation letters of the same size. See individual rules for class abbreviations.
mm. All mowers must have a functioning mechanical clutch. No chain drive from engine to transmission is allowed.
nn. Mowers must present a neat and clean appearance.
oo. No written profanity is allowed on mowers.
8. Mower Class Requirements and Designations
Mower Specifications
ALL MOTORS MUST BE OF LAWN MOWER ORIGIN
Stock Kids and Adults---Governed engine at 3650 RPM---Wheel Base is Factory Stock---front wheels Stock size---Rear wheels stock size
Super Stock and J/P Junior Prepared---Governed engine Single cylinder VIB or OHV 465 cc and under 3650 RPM 15 HP and under---Wheel Base Factory Stock---front tires13tires 15psi max---Rear Tires 16 tires 15 psi Max
Mini-Sportsman---Valve in block 4 stroke 8.5 and under 19 c.i and under **
--- Wheel Base 34 unaltered minimum---Front Wheels 4 minimum---Rear wheels 6 minimum
Sportsman---Valve in block single cylinder 4 stroke 8.5 and over---Wheel Base 39 unaltered minimum---Front wheels 5 minimum---Rear wheels 6minimum 8 maximum
Mod X--- Single OHV and Twin Opposed VIB 20 and under or unlimited---Wheel Base 39 unaltered minimum---Front Wheels 5 minimum ---Rear Wheels 6 minimum 8 maximum
Super Sportsman---All overhead valve and 2-cylinder 4 stroke 25hp and under---Wheel Base 42 unaltered minimum---Front wheels 6 minimum---Rear wheels 6 minimum 8 maximum
Pro-X---Single cylinder 4 stroke---engine Unlimited---Wheel Base 42 maximum on mid-engine chassis and 45 maximum on pan style chassis---Front wheels 4 minimum 8 maximum---rear wheels 4 minimum 8 maximum
Super Modified Single---Single Cylinder 4 stroke horizontal or vertical---unlimited---Wheel Base 42 minimum unaltered---Front Wheels 5 minimum 6 maximum---Rear Wheels--- 6minimum
8 maximum
Super Modified Twin---Twin Cylinder 4 stroke flat or OHV horizontal or vertical---25hp/44Cubic Inch Max---Wheel Base 42 minimum unaltered---Front Wheels 5 minimum 6 maximum---Rear Wheels---6minimum 8 maximum
* No overhead cams allowed
** Addresses the current usage of the same engine block covering several horsepower ranges.
STOCK MOWERS:
This class will be held as requested by individual race venues. Results from races in this class will not count towards Finals.
These are as manufactured riding lawn mowers with governed engines that do not exceed 3,650 RPM.
Any replacement parts must be exact replacement for the originals. They may not offer any performance improvements over the stock part.
Tech inspection will be for general operating condition, brakes, safety issues, RPM, and blade removal. Tech inspectors may sanction modifications to ensure safety.
SUPER STOCK (SS) and JUNIOR PREPARED (JP):
Must be a full-size lawnmower with a 39 unaltered wheelbase, front engine origin, stamped steel frame, and have a steering column located behind the motor.
Mowers will use a governed engine with a 3650 RPM maximum. RPMs will be checked at tech inspection, following the heat race and following the feature race. Mowers failing the inspection following the heat race will be placed at the rear of the field. Multiple mowers failing post-heat inspection will be gridded based upon the variance of failure in their RPMs.
Failing to report to the designated area for post race inspection will result in the loss of points for the day. If the infraction occurs following the heat race, the driver will lose registration points for the day.
Motors may be any single-cylinder valve-in-block (flathead) or overhead valve (ohv) engines 15 horsepower and under with a 465 cc maximum in the original factory location.
The engine must be as delivered from the factory, internally and externally, with only the following exceptions; air cleaner, air filter or velocity stack, open exhaust and the removal of the debris screen covering the flywheel to allow quick and easy access to the flywheel nut while checking the 8 to 1 gear ratio.
Transmission or transaxle must be shift able and of lawnmower origin. Vari-drives are not permitted.
The gear ratio in the highest gear must be 8 to 1- lockouts are not permitted. For example, while in the highest gear, the rear wheels can turn no more than one revolution every time the engine rotates eight times.
Body must be stock, without external alterations.
Discreet frame strengthening is allowed. The front axle may be reinforced, subs:censored:uted or fabricated. Racer-fabricated axles will be reviewed by the Tech Inspector to determine their apparent safety for racing. Aluminum is not permitted as the material for the axle.
Front spindles are to be a minimum of 5/8 in diameter.
Metal rims are to be used both front and rear. Rim size will be 6 diameter in the front and 8 diameter in the rear. Rear rims may be reinforced on the inside.
Front tires may be 13-15 in diameter. Rear tires will be 16 diameter.
Tire pressure may not exceed 15 psi. This will be checked immediately following the feature race.
Mowers must have steel factory decks.
Mowers must have rear bumpers (see details in section 7gg).
RPM may not be adjusted at the throttle control lever. RPMs must be adjusted at the governor spring. A screw is to be placed at the throttle control box to limit cable travel. If the throttle control is equipped with an adjustable nut at the lever on the steering wheel it must be firmly tightened and taped. No adjustment at this point on the mower is allowed.
MINI-SPORTSMAN (M):
Engines must maintain stock outward appearance with the exception of the air filter, air cleaner or velocity stack.
Crankshaft must be in original orientation and clearance hole in the frame.
Engine may be internally modified.
34 minimum wheelbase
4 minimum front wheels, 6 minimum rear wheels.
SPORTSMAN (SP) and MOD X (MX):
Engine must maintain stock outward appearance, with the exception of the air filter, air cleaner or velocity stack.
Crankshaft must be in original orientation and clearance hole in the frame.
Engine may be internally modified.
39 minimum wheelbase
Mid-engine frames not allowed
5 minimum front wheels, 6 minimum rear wheels
Crankshaft must be in original orientation
SUPER SPORTSMAN (S):
Engine must maintain stock outward appearance, with the exception of the air filter, air cleaner or velocity stack.
Crankshaft must be in original orientation and clearance hole in the frame.
Engine may be internally modified.
42 minimum wheelbase
Mid-engine frames are not allowed
6 minimum front wheels, 6 minimum rear wheels
PRO-X (PX):
Engine may be internally and externally modified.
Engine location may be modified.
Maximum wheelbase 42 on mid-engine chassis, 45 on pan style chassis.
Mid-engine frames and pan chassis may be altered to shorten wheelbase to A minimum of 37.
Pan chassis frames must maintain the original pan chassis and body parts.
Mid-engine frames may be updated, but must retain the form and substance material of the original factory frame.
Mid-engine frames are limited to a maximum width of 15 and length of 48.
Round tubing, chrome molly and aluminum are not permitted.
Drive train does not require a shift able transmission.
Drive line is open.
Wheels 4 minimum 8 maximum front and rear.
Kart tires are allowed. Snow Hogs limited to the front end only.
Stagger is allowed, offset is not.
SUPER MODIFIED SINGLE (MS)
REQUIREMENTS: Minimum age 16 years. NO ROOKIES ALLOWED. Drivers must have 1 year of ungoverned mower racing experience.
ENGINE: Open- Max 20 HP OEM rated 4-cycle single cylinder engines of lawn mower origin, either vertical or horizontal orientation. Internal and external modifications are permitted for all engines. After-market aluminum billet flywheels are MANDATORY. Modifications to the block and heads are unlimited. Block and heads must be of original OEM casting.
FUEL DELIVERY: No fuel injection, blower or turbo's. NO electric fuel pumps allowed.
IGNITION: Open.
SAFETY SHIELDS: Cowling or safety shields (blower housings) must remain, subject to safety inspection. Engines must be separated by a safety shield or stock cowling (blower housing) from the driver.
CHASSIS: Frames and parts, must retain original manufacturers (OEM) specifications (no chopping) re: wheel base, length and width. Material (steel round or square) may be added for structural strength. It is recommended that front axles be bolted or welded rigid eliminating the stock pivoting.
RIDE HEIGHT: 1.5" minimum from lowest point of chassis. 4" maximum height.
WHEEL BASE: 42" minimum.
CHASSIS WEIGHT: 275lbs minimum without driver.
OVERALL WIDTH: 42" maximum side wall to sidewall.
OFFSET: Offset is allowed but is specific. Measurement from center of frame to left tire sidewall 19". Measurement from center of frame to right tire sidewall 23".
BODY WORK: Can be customized but must retain some resemblance to a lawn tractor. All parts must be securely fastened to chassis i.e. fuel tanks, batteries, bodywork, etc.
FUEL: Only pump gas, 114-octane max (no additives). N.O.S is not permitted. No fuel injection, blowers or turbos. No electric fuel pumps permitted.
THROTTLE: Foot or trigger throttles with automatic spring return mandatory. Dual return springs are mandatory.
KILL SWITCH: Tractor must have a working tethered kill switch and be fastened to driver any time engine is running. Kill switches cannot be homemade.
EXHAUST: Is open, as long as it points down and away from driver and presents no apparent hazard.
MOWER DECKS: May be fabricated but must appear to be a deck to and must maintain a minimum 1.5 ground clearance.
SEATS: Can be of Kart origin and must be mounted in center of tractor. Must be securely mounted.
BUMPERS/NERF BARS: Not mandatory BUT highly recommended. If installed, they should meet the following specifications- height within 2" of the centerline of axles, not to protrude 2" beyond the furthest point of body or tires. Maximum width of rear bumper is 38". Maximum width front should remain inside tires and not cover the face of the tire. Side crash bars must remain 1.5" in from outside of tires. No sharp edges.
BRAKES: Hydraulic brakes mandatory, front brakes highly recommended
DRIVE TRAIN: Is open to live axle, belt or chain drive custom gearboxes or transaxles. Chain guards must be made of at least 1/8 thick material. Centrifugal clutches are permitted. In instances where custom drive train may be hazardous to driver (exposed) protective shields must be installed. Discreet chassis modifications are allowed for axle installation and reinforcement, but must maintain OEM stock wheelbase. ATV drive trains and suspensions are not permitted.
STEERING any improvements or modifications to steering are allowed and recommended. NO stock steering allowed. All steering components must be double nutted or drilled and safety wired for maximum safety.
TIRES: Go kart dirt slicks or grooved tires are allowed, (no snow hogs or deep lug tires).
WHEELS: Must be made of metal. While smaller rim sizes are permitted, 6" front wheels and 8" rear wheels are strongly recommended. All wheels must have wheel retention in the form of castle nut with cotter pins, lock collars, and snap rings, thru bolts or center bolts. Cotter pins alone are not sufficient.
SUPERMODIFIED TWIN (MT)
DRIVER REQUIREMENTS: Minimum age 18 years of age. NO ROOKIES ALLOWED. Drivers must have 1 year of ungoverned racing.
ENGINE: Open- Maximum 25 HP/44 ci max OEM rated 4-cycle twin cylinder engines of lawn mower origin, either vertical or horizontal orientation. Internal and external modifications are permitted for all engines. After-market aluminum billet flywheels are MANDATORY. Modifications to the block and heads are unlimited. Block and heads must be of original OEM casting.
FUEL DELIVERY: No fuel injection, blower or turbo's. NO electric fuel pumps allowed.
IGNITION: Open.
SAFETY SHIELDS: Cowling or safety shields (blower housings) must remain, subject to safety inspection. Engines must be separated by a safety shield or stock cowling (blower housing) from the driver.
CHASSIS: Frames and parts, must retain original manufacturers (OEM) specifications (no chopping) re: wheel base, length and width. Material (steel round or square) may be added for structural strength. It is recommended that front axles be bolted or welded rigid eliminating the stock pivoting.
RIDE HEIGHT: 1.5" minimum from lowest point of chassis. 4" maximum height.
WHEEL BASE: 42" minimum.
CHASSIS WEIGHT: 275lbs minimum without driver.
OVERALL WIDTH: 42" maximum side wall to sidewall.
OFFSET: Offset is allowed but is specific. Measurement from center of frame to left tire sidewall 19". Measurement from center of frame to right tire sidewall 23".
BODY WORK: Can be customized but must retain some resemblance to a lawn tractor. All parts must be securely fastened to chassis i.e. fuel tanks, batteries, bodywork, etc.
FUEL: Only pump gas, 114-octane max (no additives). N.O.S is not permitted. No fuel injection, blowers or turbos. No electric fuel pumps permitted.
THROTTLE: Foot or trigger throttles with automatic spring return mandatory. Dual return springs are mandatory.
KILL SWITCH: Tractor must have a working tethered kill switch and be fastened to driver any time engine is running. Kill switches cannot be homemade.
EXHAUST: Is open, as long as it points down and away from driver and presents no apparent hazard.
MOWER DECKS: May be fabricated but must appear to be a deck to and must maintain a minimum 1.5 ground clearance.
SEATS: Can be of Kart origin and must be mounted in center of tractor. Must be securely mounted.
BUMPERS/NERF BARS: Not mandatory BUT highly recommended. If installed, they should meet the following specifications- height within 2" of the centerline of axles, not to protrude 2" beyond the furthest point of body or tires. Maximum width of rear bumper is 38". Maximum width front should remain inside tires and not cover the face of the tire. Side crash bars must remain 1.5" in from outside of tires. No sharp edges.
BRAKES: Hydraulic brakes mandatory, front brakes highly recommended.
DRIVE TRAIN: Is open to live axle, belt or chain drive custom gearboxes or transaxles. Chain guards must be made of at least 1/8 thick material. Centrifugal clutches are permitted. In instances where custom drive train may be hazardous to driver (exposed) protective shields must be installed. Discreet chassis modifications are allowed for axle installation and reinforcement, but must maintain OEM stock wheelbase. ATV drive trains and suspensions are not permitted.
STEERING: any improvements or modifications to steering are allowed and recommended. NO stock steering allowed. All steering components must be double nutted or drilled and safety wired for maximum safety.
TIRES: Go kart dirt slicks or grooved tires are allowed, (no snow hogs or deep lug tires).
WHEELS: Must be made of metal. While smaller rim sizes are permitted, 6" front wheels and 8" rear wheels are strongly recommended. All wheels must have wheel retention in the form of castle nut with cotter pins, lock collars, snap rings, thru bolts or center bolts. Cotter pins alone are not sufficient.
ARMA Point Structure
Drivers participating in ARMA sanctioned national points races will receive points for their participation and finishing position. These points will be recorded with the national office on a database that covers all ARMA racers. Points will ac:censored:ulate through the racing season. The United States is divided into three regions. An imaginary line runs through Richmond, VA. Racers living in northern Virginia, Maryland, Delaware, Pennsylvania, New Jersey, West Virginia are competing in the Northern Region. Racers living below Richmond, North Carolina, South Carolina, Georgia, Tennessee, Alabama, and Florida are competing in the Southern Region. Mid-west Region drivers are designated as those living in Michigan, Ohio, Indiana, Illinois, and Wisconsin. If possible, a Southwest region will be added as well that would include Texas, California, Montana and other chapters that are in the planning stages.
In order to compete in the National Points Series a driver must race in at least two local chapter races. At the end of the season, are awarded full points for their top 5 National Points Series races. These points are be used to identify a Northern, Southern, and Mid-West Series points champion (also second through fifth place drivers) in each class. This enables points winners in the top 5 positions from each class in all three regions to go to finals and race it out to determine an overall champion, second and third in each class. Drivers competing at finals will bring with them points based upon their final ranking for the year- 400 for 1st, 350 for 2nd, 300 for 3rd, 250 for 4th and 200 for 5th. At the finals the top fifteen drivers in each class (5 Northern series drivers , 5 Southern series drivers, 5 Mid-West) will have starting positions secured in the front of the grid. The top fifteen drivers will draw for positions 1-15 on the grid for their class (number may change if less than all eligible drivers travel to compete in finals.) Other drivers in the same class will draw for the remaining positions. Finishing points will be awarded just as in any other National Points Series races. The regional driver with the highest point value for the day in each class will be designated as the champion. Second place through fifth place national points series winners would be identified in the same way.
Point Values:
50 points for registration
50 points for starting the race
50 points for finishing the race
** In order to receive points for completing a race the mower must cross the finish line under mechanical power. An exception to this rule occurs if a mower experiences mechanical problems on the white flag lap. Then the mower may be pushed by the driver across the finish line.
50 points for 5th place finishing position
100 points for 4th place finishing position
150 points for 3rd place finishing position
200 points for 2nd place finishing position
250 points for 1st place finishing position
|
